ISN Knowledge Base

Uživatelské nástroje

Nástroje pro tento web

Historie:
boot-info-upgrade-firmware-vocore-2-lite
no way to compare when less than two revisions

Rozdíly

Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.


Poslední revize
—boot-info-upgrade-firmware-vocore-2-lite [2017/04/22 13:53] – vytvořeno blazek
Řádek 1: Řádek 1:
 +====== Boot info/upgrade firmware Vocore 2 Lite ======
  
 +[[Vocore 2 Lite]]
 +
 +<code>
 +[ 1089.730000] da match,0xb8d81267511e
 +[ 1760.260000] reboot: Restarting system
 +******************************
 +Software System Reset Occurred
 +******************************
 +*** Warning - bad CRC, using default environment
 +
 +============================================
 +Ralink UBoot Version: 4.3.0.0
 +--------------------------------------------
 +ASIC 7628_MP (Port5<->None)
 +DRAM component: 512 Mbits DDR, width 16
 +DRAM bus: 16 bit
 +Total memory: 64 MBytes
 +Flash component: SPI Flash
 +Date:Jun 25 2016  Time:22:30:18
 +============================================
 +icache: sets:512, ways:4, linesz:32 ,total:65536
 +dcache: sets:256, ways:4, linesz:32 ,total:32768
 +RESET MT7628 PHY!!!!!!
 +Please choose the operation:
 +   0: Load system code then write to Flash via SERIAL.
 +   1: Load system code to SDRAM via TFTP.
 +   2: Load system code then write to Flash via TFTP.
 +   3: Boot system code via Flash (default).
 +   4: Entr boot command line interface.
 +   5: Load system code then write to Flash via USB Storage.
 +   7: Load Boot Loader code then write to Flash via Serial.
 +   8: Start Web Server to load system code.
 +   9: Load Boot Loader code then write to Flash via TFTP.
 + 0
 +
 +3: System Boot system code via Flash.
 +## Booting image at bc050000 ...
 +   Image Name:   MIPS OpenWrt Linux-3.18.29
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +   Data Size:    1146222 Bytes =  1.1 MB
 +   Load Address: 80000000
 +   Entry Point:  80000000
 +   Verifying Checksum ... OK
 +   Uncompressing Kernel Image ... OK
 +No initrd
 +## Transferring control to Linux (at address 80000000) ...
 +## Giving linux memsize in MB, 64
 +
 +Starting kernel ...
 +
 +[    0.000000] Linux version 3.18.29 (vocore@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49378) ) #2 Sat Feb 11 03:10:32 CST 2017
 +[    0.000000] Board has DDR2
 +[    0.000000] Analog PMU set to hw control
 +[    0.000000] Digital PMU set to hw control
 +[    0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
 +[    0.000000] MIPS: machine is VoCore2
 +[    0.000000] Determined physical RAM map:
 +[    0.000000]  memory: 04000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone ranges:
 +[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
 +[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
 +[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
 +[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +[    0.000000] Kernel command line: console=ttyS2,115200 rootfstype=squashfs,jffs2
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Writing ErrCtl register=0005df98
 +[    0.000000] Readback ErrCtl register=0005df98
 +[    0.000000] Memory: 61364K/65536K available (2530K kernel code, 131K rwdata, 520K rodata, 136K init, 186K bss, 4172K reserved)
 +[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
 +[    0.000000] NR_IRQS:256
 +[    0.000000] intc: using register map from devicetree
 +[    0.000000] CPU Clock: 580MHz
 +[    0.000000] clocksource_of_init: no matching clocksources found
 +[    0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
 +[    0.060000] pid_max: default: 32768 minimum: 301
 +[    0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.070000] pinctrl core: initialized pinctrl subsystem
 +[    0.080000] NET: Registered protocol family 16
 +[    0.100000] mt7621_gpio 10000600.gpio: registering 32 gpios
 +[    0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios
 +[    0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios
 +[    0.120000] Switched to clocksource MIPS
 +[    0.120000] NET: Registered protocol family 2
 +[    0.130000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.130000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.140000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.140000] TCP: reno registered
 +[    0.150000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.150000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.160000] NET: Registered protocol family 1
 +[    0.170000] futex hash table entries: 256 (order: -1, 3072 bytes)
 +[    0.180000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +[    0.180000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.200000] msgmni has been set to 119
 +[    0.210000] io scheduler noop registered
 +[    0.210000] io scheduler deadline registered (default)
 +[    0.220000] gdma-mt7628 10002800.gdma: revision: 3, channels: 16
 +[    0.230000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
 +[    0.230000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
 +[    0.240000] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
 +[    0.250000] console [ttyS2] disabled
 +[    0.260000] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
 +[    0.270000] console [ttyS2] enabled
 +[    0.270000] console [ttyS2] enabled
 +[    0.270000] bootconsole [early0] disabled
 +[    0.270000] bootconsole [early0] disabled
 +[    0.280000] spi-mt7621 10000b00.spi: sys_freq: 193333333
 +[    0.290000] m25p80 spi32766.0: found gd25q64, expected en25q64
 +[    0.300000] m25p80 spi32766.0: gd25q64 (8192 Kbytes)
 +[    0.300000] m25p80 spi32766.0: using chunked io
 +[    0.310000] 4 ofpart partitions found on MTD device spi32766.0
 +[    0.310000] Creating 4 MTD partitions on "spi32766.0":
 +[    0.320000] 0x000000000000-0x000000030000 : "u-boot"
 +[    0.330000] 0x000000030000-0x000000040000 : "u-boot-env"
 +[    0.330000] 0x000000040000-0x000000050000 : "factory"
 +[    0.340000] 0x000000050000-0x000000800000 : "firmware"
 +[    0.380000] 2 uimage-fw partitions found on MTD device firmware
 +[    0.380000] 0x000000050000-0x000000167dae : "kernel"
 +[    0.390000] 0x000000167dae-0x000000800000 : "rootfs"
 +[    0.390000] mtd: device 5 (rootfs) set to be root filesystem
 +[    0.400000] 1 squashfs-split partitions found on MTD device rootfs
 +[    0.410000] 0x0000006e0000-0x000000800000 : "rootfs_data"
 +[    0.420000] ralink_soc_eth 10100000.ethernet: generated random MAC address 56:77:1c:e8:9e:77
 +[    0.430000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
 +[    0.440000] mt7621_wdt 10000120.watchdog: Initialized
 +[    0.440000] TCP: cubic registered
 +[    0.450000] NET: Registered protocol family 17
 +[    0.450000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
 +[    0.470000] 8021q: 802.1Q VLAN Support v1.8
 +[    0.480000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
 +[    0.490000] Freeing unused kernel memory: 136K (8031e000 - 80340000)
 +[    2.290000] init: Console is alive
 +[    2.290000] init: - watchdog -
 +[    5.670000] usbcore: registered new interface driver usbfs
 +[    5.680000] usbcore: registered new interface driver hub
 +[    5.680000] usbcore: registered new device driver usb
 +[    5.690000] exFAT: Version 1.2.9
 +[    5.750000] SCSI subsystem initialized
 +[    5.750000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 +[    5.760000] ehci-platform: EHCI generic platform driver
 +[    5.780000] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
 +[    5.790000] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
 +[    5.790000] ehci-platform 101c0000.ehci: EHCI Host Controller
 +[    5.800000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
 +[    5.810000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
 +[    5.830000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
 +[    5.830000] hub 1-0:1.0: USB hub found
 +[    5.840000] hub 1-0:1.0: 1 port detected
 +[    5.840000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
 +[    5.850000] ohci-platform: OHCI generic platform driver
 +[    5.860000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
 +[    5.860000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
 +[    5.870000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
 +[    5.940000] hub 2-0:1.0: USB hub found
 +[    5.940000] hub 2-0:1.0: 1 port detected
 +[    5.950000] usbcore: registered new interface driver usb-storage
 +[    6.320000] init: - preinit -
 +[    7.460000] rt305x-esw 10110000.esw: link changed 0x00
 +[    7.660000] random: mktemp urandom read with 12 bits of entropy available
 +Press the [f] key and hit [enter] to enter failsafe mode
 +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
 +[   10.900000] mount_root: loading kmods from internal overlay
 +[   11.490000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
 +[   11.500000] jffs2_build_filesystem(): unlocking the mtd device... done.
 +[   11.500000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
 +[   16.320000] jffs2: notice: (363) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
 +[   16.340000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
 +[   16.340000] block: unable to load configuration (fstab: Entry not found)
 +[   16.350000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
 +[   16.360000] block: unable to load configuration (fstab: Entry not found)
 +[   16.360000] block: attempting to load /etc/config/fstab
 +[   16.370000] block: unable to load configuration (fstab: Entry not found)
 +[   16.380000] block: no usable configuration
 +[   16.480000] jffs2: notice: (360) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
 +[   16.990000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
 +[   17.000000] block: unable to load configuration (fstab: Entry not found)
 +[   17.010000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
 +[   17.020000] block: unable to load configuration (fstab: Entry not found)
 +[   17.020000] block: attempting to load /etc/config/fstab
 +[   17.030000] block: unable to load configuration (fstab: Entry not found)
 +[   17.030000] block: no usable configuration
 +[   17.040000] mount_root: overlay filesystem has not been fully initialized yet
 +[   17.050000] mount_root: switching to jffs2 overlay
 +- config restore -
 +[   17.810000] procd: - early -
 +[   17.820000] procd: - watchdog -
 +[   18.720000] procd: - ubus -
 +Command failed: Not found
 +[   19.750000] procd: - init -
 +Please press Enter to activate this console.
 +[   20.910000] NET: Registered protocol family 10
 +[   20.980000] ntfs: driver 2.1.31 [Flags: R/O MODULE].
 +[   21.070000] tun: Universal TUN/TAP device driver, 1.6
 +[   21.070000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
 +[   21.100000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[   21.140000] i2c /dev entries driver
 +[   22.410000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
 +[   22.420000] <-- RTMPAllocAdapterBlock, Status=0
 +[   22.450000] i2c-gpio i2c-gpio: using pins 5 (SDA) and 4 (SCL)
 +[   22.470000] Linux video capture interface: v2.00
 +[   22.490000] mt7628-i2s 10000a00.i2s: loaded, sys freq is 480MHz.
 +[   22.500000] es8388_codec_probe
 +[   22.510000] es8388_reset
 +[   22.530000] set system reference clock(mclk) to 12MHz.
 +[   22.540000] mt7628-audio audio-card: es8388-hifi <-> 10000a00.i2s mapping ok
 +[   22.550000] mt7628-audio audio-card: load
 +[   22.560000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   22.580000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
 +[   22.610000] usbcore: registered new interface driver usblp
 +[   22.620000] usbcore: registered new interface driver uvcvideo
 +[   22.630000] USB Video Class driver (1.1.1)
 +[   22.650000] xt_time: kernel timezone is -0000
 +[   22.670000] PPP generic driver version 2.4.2
 +[   22.670000] NET: Registered protocol family 24
 +[   30.540000] device eth0.1 entered promiscuous mode
 +[   30.550000] device eth0 entered promiscuous mode
 +[   30.560000] br-lan: port 1(eth0.1) entered forwarding state
 +[   30.560000] br-lan: port 1(eth0.1) entered forwarding state
 +[   32.560000] br-lan: port 1(eth0.1) entered forwarding state
 +[   32.770000] efuse_probe: efuse = 10000012
 +[   32.770000] net ra0: Direct firmware load for mt7628.eeprom failed with error -2
 +[   32.780000] net ra0: Falling back to user helper
 +[   38.190000] tssi_0_target_pwr_g_band = 35
 +[   38.190000] tssi_1_target_pwr_g_band = 35
 +[   43.830000] <==== rt28xx_init, Status=0
 +[   45.070000] device ra0 entered promiscuous mode
 +[   45.070000] br-lan: port 2(ra0) entered forwarding state
 +[   45.080000] br-lan: port 2(ra0) entered forwarding state
 +[   45.720000] br-lan: port 2(ra0) entered disabled state
 +[   45.720000] br-lan: port 1(eth0.1) entered disabled state
 +[   45.730000] device eth0.1 left promiscuous mode
 +[   45.740000] br-lan: port 1(eth0.1) entered disabled state
 +[   45.740000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
 +[   45.760000] device ra0 left promiscuous mode
 +[   45.760000] br-lan: port 2(ra0) entered disabled state
 +[   46.110000] device eth0 left promiscuous mode
 +[   47.860000] device eth0.1 entered promiscuous mode
 +[   47.860000] device eth0 entered promiscuous mode
 +[   47.870000] br-lan: port 1(eth0.1) entered forwarding state
 +[   47.880000] br-lan: port 1(eth0.1) entered forwarding state
 +[   49.820000] device ra0 entered promiscuous mode
 +[   49.820000] br-lan: port 2(ra0) entered forwarding state
 +[   49.830000] br-lan: port 2(ra0) entered forwarding state
 +[   49.880000] br-lan: port 1(eth0.1) entered forwarding state
 +[   51.830000] br-lan: port 2(ra0) entered forwarding state
 +[   69.550000] random: nonblocking pool is initialized
 +[  399.800000] da match,0xb8d81267511e
 +
 +
 +
 +BusyBox v1.23.2 (2017-01-25 15:51:22 CST) built-in shell (ash)
 +
 +  _______                     ________        __
 + |       |.-----.-----.-----.|  |  |  |.----.|  |_
 + |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 + |_______||   __|_____|__|__||________||__|  |____|
 +          |__| W I R E L E S S   F R E E D O M
 + -----------------------------------------------------
 + CHAOS CALMER (Chaos Calmer, r49378)
 + -----------------------------------------------------
 +  * 1 1/2 oz Gin            Shake with a glassful
 +  * 1/4 oz Triple Sec       of broken ice and pour
 +  * 3/4 oz Lime Juice       unstrained into a goblet.
 +  * 1 1/2 oz Orange Juice
 +  * 1 tsp. Grenadine Syrup
 + -----------------------------------------------------
 +root@OpenWrt:/#
 +</code>
boot-info-upgrade-firmware-vocore-2-lite.txt · Poslední úprava: 2023/12/26 19:13 autor: 127.0.0.1