ISN Knowledge Base

Tato stránka je pouze pro čtení. Můžete si pouze prohlédnout zdrojový kód, ale ne ho měnit. Zeptejte se správce, pokud si myslíte, že něco není v pořádku.
====== Boot info/upgrade firmware Vocore 2 Lite ======

[[Vocore 2 Lite]]

<code>
[ 1089.730000] da match,0xb8d81267511e
[ 1760.260000] reboot: Restarting system
******************************
Software System Reset Occurred
******************************
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jun 25 2016  Time:22:30:18
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
RESET MT7628 PHY!!!!!!
Please choose the operation:
   0: Load system code then write to Flash via SERIAL.
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   5: Load system code then write to Flash via USB Storage.
   7: Load Boot Loader code then write to Flash via Serial.
   8: Start Web Server to load system code.
   9: Load Boot Loader code then write to Flash via TFTP.
 0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.29
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1146222 Bytes =  1.1 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 3.18.29 (vocore@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49378) ) #2 Sat Feb 11 03:10:32 CST 2017
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] MIPS: machine is VoCore2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS2,115200 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=0005df98
[    0.000000] Readback ErrCtl register=0005df98
[    0.000000] Memory: 61364K/65536K available (2530K kernel code, 131K rwdata, 520K rodata, 136K init, 186K bss, 4172K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] intc: using register map from devicetree
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource_of_init: no matching clocksources found
[    0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070000] pinctrl core: initialized pinctrl subsystem
[    0.080000] NET: Registered protocol family 16
[    0.100000] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.120000] Switched to clocksource MIPS
[    0.120000] NET: Registered protocol family 2
[    0.130000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.130000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.140000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.140000] TCP: reno registered
[    0.150000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.150000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.160000] NET: Registered protocol family 1
[    0.170000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.180000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.180000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.200000] msgmni has been set to 119
[    0.210000] io scheduler noop registered
[    0.210000] io scheduler deadline registered (default)
[    0.220000] gdma-mt7628 10002800.gdma: revision: 3, channels: 16
[    0.230000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    0.230000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
[    0.240000] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
[    0.250000] console [ttyS2] disabled
[    0.260000] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
[    0.270000] console [ttyS2] enabled
[    0.270000] console [ttyS2] enabled
[    0.270000] bootconsole [early0] disabled
[    0.270000] bootconsole [early0] disabled
[    0.280000] spi-mt7621 10000b00.spi: sys_freq: 193333333
[    0.290000] m25p80 spi32766.0: found gd25q64, expected en25q64
[    0.300000] m25p80 spi32766.0: gd25q64 (8192 Kbytes)
[    0.300000] m25p80 spi32766.0: using chunked io
[    0.310000] 4 ofpart partitions found on MTD device spi32766.0
[    0.310000] Creating 4 MTD partitions on "spi32766.0":
[    0.320000] 0x000000000000-0x000000030000 : "u-boot"
[    0.330000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.330000] 0x000000040000-0x000000050000 : "factory"
[    0.340000] 0x000000050000-0x000000800000 : "firmware"
[    0.380000] 2 uimage-fw partitions found on MTD device firmware
[    0.380000] 0x000000050000-0x000000167dae : "kernel"
[    0.390000] 0x000000167dae-0x000000800000 : "rootfs"
[    0.390000] mtd: device 5 (rootfs) set to be root filesystem
[    0.400000] 1 squashfs-split partitions found on MTD device rootfs
[    0.410000] 0x0000006e0000-0x000000800000 : "rootfs_data"
[    0.420000] ralink_soc_eth 10100000.ethernet: generated random MAC address 56:77:1c:e8:9e:77
[    0.430000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[    0.440000] mt7621_wdt 10000120.watchdog: Initialized
[    0.440000] TCP: cubic registered
[    0.450000] NET: Registered protocol family 17
[    0.450000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.470000] 8021q: 802.1Q VLAN Support v1.8
[    0.480000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    0.490000] Freeing unused kernel memory: 136K (8031e000 - 80340000)
[    2.290000] init: Console is alive
[    2.290000] init: - watchdog -
[    5.670000] usbcore: registered new interface driver usbfs
[    5.680000] usbcore: registered new interface driver hub
[    5.680000] usbcore: registered new device driver usb
[    5.690000] exFAT: Version 1.2.9
[    5.750000] SCSI subsystem initialized
[    5.750000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.760000] ehci-platform: EHCI generic platform driver
[    5.780000] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
[    5.790000] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
[    5.790000] ehci-platform 101c0000.ehci: EHCI Host Controller
[    5.800000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    5.810000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    5.830000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    5.830000] hub 1-0:1.0: USB hub found
[    5.840000] hub 1-0:1.0: 1 port detected
[    5.840000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.850000] ohci-platform: OHCI generic platform driver
[    5.860000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    5.860000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    5.870000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    5.940000] hub 2-0:1.0: USB hub found
[    5.940000] hub 2-0:1.0: 1 port detected
[    5.950000] usbcore: registered new interface driver usb-storage
[    6.320000] init: - preinit -
[    7.460000] rt305x-esw 10110000.esw: link changed 0x00
[    7.660000] random: mktemp urandom read with 12 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   10.900000] mount_root: loading kmods from internal overlay
[   11.490000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[   11.500000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   11.500000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[   16.320000] jffs2: notice: (363) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   16.340000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   16.340000] block: unable to load configuration (fstab: Entry not found)
[   16.350000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   16.360000] block: unable to load configuration (fstab: Entry not found)
[   16.360000] block: attempting to load /etc/config/fstab
[   16.370000] block: unable to load configuration (fstab: Entry not found)
[   16.380000] block: no usable configuration
[   16.480000] jffs2: notice: (360) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   16.990000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   17.000000] block: unable to load configuration (fstab: Entry not found)
[   17.010000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   17.020000] block: unable to load configuration (fstab: Entry not found)
[   17.020000] block: attempting to load /etc/config/fstab
[   17.030000] block: unable to load configuration (fstab: Entry not found)
[   17.030000] block: no usable configuration
[   17.040000] mount_root: overlay filesystem has not been fully initialized yet
[   17.050000] mount_root: switching to jffs2 overlay
- config restore -
[   17.810000] procd: - early -
[   17.820000] procd: - watchdog -
[   18.720000] procd: - ubus -
Command failed: Not found
[   19.750000] procd: - init -
Please press Enter to activate this console.
[   20.910000] NET: Registered protocol family 10
[   20.980000] ntfs: driver 2.1.31 [Flags: R/O MODULE].
[   21.070000] tun: Universal TUN/TAP device driver, 1.6
[   21.070000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   21.100000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   21.140000] i2c /dev entries driver
[   22.410000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
[   22.420000] <-- RTMPAllocAdapterBlock, Status=0
[   22.450000] i2c-gpio i2c-gpio: using pins 5 (SDA) and 4 (SCL)
[   22.470000] Linux video capture interface: v2.00
[   22.490000] mt7628-i2s 10000a00.i2s: loaded, sys freq is 480MHz.
[   22.500000] es8388_codec_probe
[   22.510000] es8388_reset
[   22.530000] set system reference clock(mclk) to 12MHz.
[   22.540000] mt7628-audio audio-card: es8388-hifi <-> 10000a00.i2s mapping ok
[   22.550000] mt7628-audio audio-card: load
[   22.560000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   22.580000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[   22.610000] usbcore: registered new interface driver usblp
[   22.620000] usbcore: registered new interface driver uvcvideo
[   22.630000] USB Video Class driver (1.1.1)
[   22.650000] xt_time: kernel timezone is -0000
[   22.670000] PPP generic driver version 2.4.2
[   22.670000] NET: Registered protocol family 24
[   30.540000] device eth0.1 entered promiscuous mode
[   30.550000] device eth0 entered promiscuous mode
[   30.560000] br-lan: port 1(eth0.1) entered forwarding state
[   30.560000] br-lan: port 1(eth0.1) entered forwarding state
[   32.560000] br-lan: port 1(eth0.1) entered forwarding state
[   32.770000] efuse_probe: efuse = 10000012
[   32.770000] net ra0: Direct firmware load for mt7628.eeprom failed with error -2
[   32.780000] net ra0: Falling back to user helper
[   38.190000] tssi_0_target_pwr_g_band = 35
[   38.190000] tssi_1_target_pwr_g_band = 35
[   43.830000] <==== rt28xx_init, Status=0
[   45.070000] device ra0 entered promiscuous mode
[   45.070000] br-lan: port 2(ra0) entered forwarding state
[   45.080000] br-lan: port 2(ra0) entered forwarding state
[   45.720000] br-lan: port 2(ra0) entered disabled state
[   45.720000] br-lan: port 1(eth0.1) entered disabled state
[   45.730000] device eth0.1 left promiscuous mode
[   45.740000] br-lan: port 1(eth0.1) entered disabled state
[   45.740000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[   45.760000] device ra0 left promiscuous mode
[   45.760000] br-lan: port 2(ra0) entered disabled state
[   46.110000] device eth0 left promiscuous mode
[   47.860000] device eth0.1 entered promiscuous mode
[   47.860000] device eth0 entered promiscuous mode
[   47.870000] br-lan: port 1(eth0.1) entered forwarding state
[   47.880000] br-lan: port 1(eth0.1) entered forwarding state
[   49.820000] device ra0 entered promiscuous mode
[   49.820000] br-lan: port 2(ra0) entered forwarding state
[   49.830000] br-lan: port 2(ra0) entered forwarding state
[   49.880000] br-lan: port 1(eth0.1) entered forwarding state
[   51.830000] br-lan: port 2(ra0) entered forwarding state
[   69.550000] random: nonblocking pool is initialized
[  399.800000] da match,0xb8d81267511e



BusyBox v1.23.2 (2017-01-25 15:51:22 CST) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 CHAOS CALMER (Chaos Calmer, r49378)
 -----------------------------------------------------
  * 1 1/2 oz Gin            Shake with a glassful
  * 1/4 oz Triple Sec       of broken ice and pour
  * 3/4 oz Lime Juice       unstrained into a goblet.
  * 1 1/2 oz Orange Juice
  * 1 tsp. Grenadine Syrup
 -----------------------------------------------------
root@OpenWrt:/#
</code>