====== Boot info/upgrade firmware Vocore 2 Lite ====== [[Vocore 2 Lite]] [ 1089.730000] da match,0xb8d81267511e [ 1760.260000] reboot: Restarting system ****************************** Software System Reset Occurred ****************************** *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.3.0.0 -------------------------------------------- ASIC 7628_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Jun 25 2016 Time:22:30:18 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 RESET MT7628 PHY!!!!!! Please choose the operation: 0: Load system code then write to Flash via SERIAL. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 5: Load system code then write to Flash via USB Storage. 7: Load Boot Loader code then write to Flash via Serial. 8: Start Web Server to load system code. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... Image Name: MIPS OpenWrt Linux-3.18.29 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1146222 Bytes = 1.1 MB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 3.18.29 (vocore@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49378) ) #2 Sat Feb 11 03:10:32 CST 2017 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc) [ 0.000000] MIPS: machine is VoCore2 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS2,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0005df98 [ 0.000000] Readback ErrCtl register=0005df98 [ 0.000000] Memory: 61364K/65536K available (2530K kernel code, 131K rwdata, 520K rodata, 136K init, 186K bss, 4172K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] intc: using register map from devicetree [ 0.000000] CPU Clock: 580MHz [ 0.000000] clocksource_of_init: no matching clocksources found [ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] pinctrl core: initialized pinctrl subsystem [ 0.080000] NET: Registered protocol family 16 [ 0.100000] mt7621_gpio 10000600.gpio: registering 32 gpios [ 0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios [ 0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios [ 0.120000] Switched to clocksource MIPS [ 0.120000] NET: Registered protocol family 2 [ 0.130000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.130000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.140000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.140000] TCP: reno registered [ 0.150000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.150000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.160000] NET: Registered protocol family 1 [ 0.170000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.180000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.180000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.200000] msgmni has been set to 119 [ 0.210000] io scheduler noop registered [ 0.210000] io scheduler deadline registered (default) [ 0.220000] gdma-mt7628 10002800.gdma: revision: 3, channels: 16 [ 0.230000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.230000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A [ 0.240000] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A [ 0.250000] console [ttyS2] disabled [ 0.260000] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A [ 0.270000] console [ttyS2] enabled [ 0.270000] console [ttyS2] enabled [ 0.270000] bootconsole [early0] disabled [ 0.270000] bootconsole [early0] disabled [ 0.280000] spi-mt7621 10000b00.spi: sys_freq: 193333333 [ 0.290000] m25p80 spi32766.0: found gd25q64, expected en25q64 [ 0.300000] m25p80 spi32766.0: gd25q64 (8192 Kbytes) [ 0.300000] m25p80 spi32766.0: using chunked io [ 0.310000] 4 ofpart partitions found on MTD device spi32766.0 [ 0.310000] Creating 4 MTD partitions on "spi32766.0": [ 0.320000] 0x000000000000-0x000000030000 : "u-boot" [ 0.330000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.330000] 0x000000040000-0x000000050000 : "factory" [ 0.340000] 0x000000050000-0x000000800000 : "firmware" [ 0.380000] 2 uimage-fw partitions found on MTD device firmware [ 0.380000] 0x000000050000-0x000000167dae : "kernel" [ 0.390000] 0x000000167dae-0x000000800000 : "rootfs" [ 0.390000] mtd: device 5 (rootfs) set to be root filesystem [ 0.400000] 1 squashfs-split partitions found on MTD device rootfs [ 0.410000] 0x0000006e0000-0x000000800000 : "rootfs_data" [ 0.420000] ralink_soc_eth 10100000.ethernet: generated random MAC address 56:77:1c:e8:9e:77 [ 0.430000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 [ 0.440000] mt7621_wdt 10000120.watchdog: Initialized [ 0.440000] TCP: cubic registered [ 0.450000] NET: Registered protocol family 17 [ 0.450000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.470000] 8021q: 802.1Q VLAN Support v1.8 [ 0.480000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 0.490000] Freeing unused kernel memory: 136K (8031e000 - 80340000) [ 2.290000] init: Console is alive [ 2.290000] init: - watchdog - [ 5.670000] usbcore: registered new interface driver usbfs [ 5.680000] usbcore: registered new interface driver hub [ 5.680000] usbcore: registered new device driver usb [ 5.690000] exFAT: Version 1.2.9 [ 5.750000] SCSI subsystem initialized [ 5.750000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.760000] ehci-platform: EHCI generic platform driver [ 5.780000] phy phy-10120000.usbphy.0: remote usb device wakeup disabled [ 5.790000] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz [ 5.790000] ehci-platform 101c0000.ehci: EHCI Host Controller [ 5.800000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 5.810000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 5.830000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 5.830000] hub 1-0:1.0: USB hub found [ 5.840000] hub 1-0:1.0: 1 port detected [ 5.840000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.850000] ohci-platform: OHCI generic platform driver [ 5.860000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller [ 5.860000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 5.870000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 5.940000] hub 2-0:1.0: USB hub found [ 5.940000] hub 2-0:1.0: 1 port detected [ 5.950000] usbcore: registered new interface driver usb-storage [ 6.320000] init: - preinit - [ 7.460000] rt305x-esw 10110000.esw: link changed 0x00 [ 7.660000] random: mktemp urandom read with 12 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.900000] mount_root: loading kmods from internal overlay [ 11.490000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000 [ 11.500000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 11.500000] jffs2_build_filesystem(): erasing all blocks after the end marker... done. [ 16.320000] jffs2: notice: (363) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 16.340000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 16.340000] block: unable to load configuration (fstab: Entry not found) [ 16.350000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab [ 16.360000] block: unable to load configuration (fstab: Entry not found) [ 16.360000] block: attempting to load /etc/config/fstab [ 16.370000] block: unable to load configuration (fstab: Entry not found) [ 16.380000] block: no usable configuration [ 16.480000] jffs2: notice: (360) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 16.990000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 17.000000] block: unable to load configuration (fstab: Entry not found) [ 17.010000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab [ 17.020000] block: unable to load configuration (fstab: Entry not found) [ 17.020000] block: attempting to load /etc/config/fstab [ 17.030000] block: unable to load configuration (fstab: Entry not found) [ 17.030000] block: no usable configuration [ 17.040000] mount_root: overlay filesystem has not been fully initialized yet [ 17.050000] mount_root: switching to jffs2 overlay - config restore - [ 17.810000] procd: - early - [ 17.820000] procd: - watchdog - [ 18.720000] procd: - ubus - Command failed: Not found [ 19.750000] procd: - init - Please press Enter to activate this console. [ 20.910000] NET: Registered protocol family 10 [ 20.980000] ntfs: driver 2.1.31 [Flags: R/O MODULE]. [ 21.070000] tun: Universal TUN/TAP device driver, 1.6 [ 21.070000] tun: (C) 1999-2004 Max Krasnyansky [ 21.100000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 21.140000] i2c /dev entries driver [ 22.410000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x [ 22.420000] <-- RTMPAllocAdapterBlock, Status=0 [ 22.450000] i2c-gpio i2c-gpio: using pins 5 (SDA) and 4 (SCL) [ 22.470000] Linux video capture interface: v2.00 [ 22.490000] mt7628-i2s 10000a00.i2s: loaded, sys freq is 480MHz. [ 22.500000] es8388_codec_probe [ 22.510000] es8388_reset [ 22.530000] set system reference clock(mclk) to 12MHz. [ 22.540000] mt7628-audio audio-card: es8388-hifi <-> 10000a00.i2s mapping ok [ 22.550000] mt7628-audio audio-card: load [ 22.560000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 22.580000] nf_conntrack version 0.5.0 (960 buckets, 3840 max) [ 22.610000] usbcore: registered new interface driver usblp [ 22.620000] usbcore: registered new interface driver uvcvideo [ 22.630000] USB Video Class driver (1.1.1) [ 22.650000] xt_time: kernel timezone is -0000 [ 22.670000] PPP generic driver version 2.4.2 [ 22.670000] NET: Registered protocol family 24 [ 30.540000] device eth0.1 entered promiscuous mode [ 30.550000] device eth0 entered promiscuous mode [ 30.560000] br-lan: port 1(eth0.1) entered forwarding state [ 30.560000] br-lan: port 1(eth0.1) entered forwarding state [ 32.560000] br-lan: port 1(eth0.1) entered forwarding state [ 32.770000] efuse_probe: efuse = 10000012 [ 32.770000] net ra0: Direct firmware load for mt7628.eeprom failed with error -2 [ 32.780000] net ra0: Falling back to user helper [ 38.190000] tssi_0_target_pwr_g_band = 35 [ 38.190000] tssi_1_target_pwr_g_band = 35 [ 43.830000] <==== rt28xx_init, Status=0 [ 45.070000] device ra0 entered promiscuous mode [ 45.070000] br-lan: port 2(ra0) entered forwarding state [ 45.080000] br-lan: port 2(ra0) entered forwarding state [ 45.720000] br-lan: port 2(ra0) entered disabled state [ 45.720000] br-lan: port 1(eth0.1) entered disabled state [ 45.730000] device eth0.1 left promiscuous mode [ 45.740000] br-lan: port 1(eth0.1) entered disabled state [ 45.740000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [ 45.760000] device ra0 left promiscuous mode [ 45.760000] br-lan: port 2(ra0) entered disabled state [ 46.110000] device eth0 left promiscuous mode [ 47.860000] device eth0.1 entered promiscuous mode [ 47.860000] device eth0 entered promiscuous mode [ 47.870000] br-lan: port 1(eth0.1) entered forwarding state [ 47.880000] br-lan: port 1(eth0.1) entered forwarding state [ 49.820000] device ra0 entered promiscuous mode [ 49.820000] br-lan: port 2(ra0) entered forwarding state [ 49.830000] br-lan: port 2(ra0) entered forwarding state [ 49.880000] br-lan: port 1(eth0.1) entered forwarding state [ 51.830000] br-lan: port 2(ra0) entered forwarding state [ 69.550000] random: nonblocking pool is initialized [ 399.800000] da match,0xb8d81267511e BusyBox v1.23.2 (2017-01-25 15:51:22 CST) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- CHAOS CALMER (Chaos Calmer, r49378) ----------------------------------------------------- * 1 1/2 oz Gin Shake with a glassful * 1/4 oz Triple Sec of broken ice and pour * 3/4 oz Lime Juice unstrained into a goblet. * 1 1/2 oz Orange Juice * 1 tsp. Grenadine Syrup ----------------------------------------------------- root@OpenWrt:/#